Home > Drives >

Copley Controls: CANopen Stepnet Micro Module (STL-055 Series)
opley Controls: CANopen Stepnet Micro Module (STL-055 Series)

20-75 VDC & 115-230 VAC Digital Drives for Stepper Motors


 

Price : $359.00

Quantity in Stock:1

Order #: STL-055-04
Qty:

Description Specifications and Drawings
 

Copley Controls: CANopen Stepnet Micro Module (STL-055 Series)

20-75 VDC & 115-230 VAC Digital Drives for Stepper Motors


Descriptio
n

Stepnet Micro Module is a stepper motor driver in a 4in2 pc-board mounting package that combines CANopen networking with 100% digital control of stepper motors. Power output is compatible with most NEMA 17 and 23 size stepper motors. The small footprint is well-suited for desktop instrumentation and enables motor drive, interface, power supply, and control circuits to be combined on a single PC board.

Stepnet Micro Module can also operate as a stand-alone driver taking incremental position commands from stepmotor controllers in Step/Direction or CU/CD format, as well as A/B quadrature commands from a master-encoder. Step to motor position ratio is programmable for electronic gearing.

When fitted with an incremental encoder a stepper motor can be operated as a brushless servo motor using Stepnet Micro Module’s Servo Mode feature, or as a conventional stepper with stall detection. Setup is fast and simple using CME 2™ software operating under Windows® and communicating with Stepnet Micro Module via an RS-232 link. CAN address selection is by digital inputs or can be programmed into driver flash memory.

As a CANopen node Stepnet Micro Module operates as a Motion Control Device under the DSP-402 protocol of the CANopen DS-301 V4.01 (EN 50325-4) application layer. DSP-402 modes supported include: Profile Position, Profile Velocity, Interpolated Position (PVT), and Homing. When in Servo Mode, operating the stepper as a servo motor with encoder feedback, Profile Torque mode is available.

Profile Position Mode does a complete motion index on command with S-curve acceleration & deceleration, top speed, and distance programmable. In PVT mode, the controller sends out a sequence of points each of which is an increment of a larger, more complex move than that of a single index or profile. Profile Velocity mode has acceleration, deceleration, and velocity control without a position set point. Homing mode is configurable to work with a combination of limit and home switches such that the driver moves the motor into a position that has an absolute reference to some part of the machine.

One logic input [IN1] is dedicated for the driver Enable function. The other eleven are programmable as CAN address, limit & home switches, stepper pulse inputs, A/B master encoder, motor feedback encoder, reset, motion abort, or motor-temperature. There are four programmable logic outputs for reporting a driver fault, or other status indications. When operating as a CAN node, inputs and outputs can be used as general-purpose I/O with no link to amplifier functions.

An Aux HV input is provided for “keep alive” power that preserves the driver data (e.g. current position) and CANopen operation if +HV has been removed as in an emergency-stop situation. This enables the control system to monitor drive status and to enable an orderly recovery without a full system reset, and “homing” of all axes. Operation from transformer-isolated DC power supplies saves cost in multi-axis systems.

Control Modes

  • Indexer, Point-to-Point, PVT

  • Camming, Gearing

  • Position, Velocity, Torque [Servo Mode]

  • Position (Microstepping)

Command Interface

  • CANopen

  • ASCII and discrete I/O

  • Stepper commands

  • PWM velocity/torque command

  • Master encoder [Gearing/Camming]

Communications

  • CANopen

  • RS-232

Feedback

  • Digital Quad A/B encoder

I/O - Digital

  • 12 inputs, 4 outputs

Dimensions: mm [in]

  • 64 x 41 x 16 [2.5 x 1.6 x 0.6]


Share your knowledge of this product. Be the first to write a review »